As part of a refined supply chain, V-TEK is your single source of fully qualified consumable products. Hey there, we appreciate your interest in working with V-TEK, you've made some good decisions so far today. We want to make sure we make good decisions too, by properly understanding what your business needs are.
Since we are able to customize all of our equipment to our customer's specific needs, the more information you put on this note to us, the stronger our offering will look to you. Request Quote. Options Netbook with security bracket and software for controls. Related Supplies As an equipment manufacturer, V-TEK collaborates with major tape and reel companies to ensure their products are compatible with ours.
Tape Reels Auxiliary Supplies. PT Peel Force Tester. TM Automatic Taping Machine. TM Manual Taping Machine. Note: The PT is shipped with a carriage clamp attached to the carriage assembly to prevent carriage movement during shipment. AC Receptacle AC power supply plug. Load Cell Position Screw B. Load Cell C. Idler Wheel B. Calibration Jig C. Carriage Front Track Guide D. Sprocket Wheel E. Track Adjustment Knob F. Carriage Clamp remove before operation D Serial Plate When positioning the PT, choose an area that is not located below overhead gantries, walkways or power lines to ensure objects or liquids cannot be dropped on the machine from overhead.
Page 19 Chapter 2: Setup When loading, unloading or running the PT, the operator should stand in front of the machine controller to assure easy access to all controls. This position also allows the operator to view all parts of the PT while it is in operation. Page 21 Chapter 2: Setup 2. Remove the thumb screw on the left side of the machine.. Figure 2. Lift off the top of the PT Set the security bracket on top of the PT Reassemble the top of the PT Page Software Setup 3.
Once Net Framework is installed, return to the flash drive and double click S vx. Double click S vx. An Application Install screen will appear. Click on Next Figure 2.
Page 24 6. The Ready to Install Program screen will open. Click Install. The Install Shield Wizard Completed screen will open. Click Finish to complete installation.. The PT Icon will now appear on the desktop. Software Setup D As shown below, find the unknown device in the Device Manager.
Right click the device and select Update Driver Software. Page 27 Chapter 2: Setup 7. For bit systems this location needs to be x When auto tension is selected and a value is entered, the peel force graph will wait until the auto tension value is reached. Page 29 Chapter 2: Setup 3. The Supervisor Settings screen will open. Enter the Tension Threshold value and the Tension Delay value in milliseconds. The delay is the time from which the carriage assembly starts moving and when the graph starts plotting.
Page 30 6. The Tensioning message will flash over the graph until the Auto Tension Value is exceeded. The PT will then automatically reset the graph and begin plotting the peel force test. Page Save Mode Setup 5. Select Browse and choose the desired direc- tory in which to save the file. Please refer to the validation instructions on page To perform a peel force test, run out a strip of empty, sealed carrier about 6 to 12 inches long.
Page 33 Adjust the thumb screw on the left side of the machine as needed. Note: The PT software must be configured with the correct test parameters before continuing. For test configuration details, see Chapter 3: Software. Press the Start Test button in the Main Screen. The PT will begin moving the carriage and graphing the results. When complete, the test will stop automatically when it reaches the preset Pull Length.
You may also press the Stop Test button when enough data has been gathered to complete the test. Page Pt Software Found on included flash drive. Introduction This document provides the basic instructions for operating the PT Peel Force Tester software package. This program will operate the carrier tape drive assembly and generate a graphic dis- play of the peel force required to remove the cover tape.
This screen is used to configure peel tests, set test parameters, perform tests and observe test results. All of the fields will be blank.
Figure 3. The printout can then be kept for records. Print setup allows the user to select a printer and configure print settings. The Exit command will close the PT Software program.
Any unsaved data will be lost. Its fields include Supplier, Type, and Lot Number Sealtape Fields The Sealtape section is used to track information about the seal tape also known as cover tape that is used in a test. In this case, the pull length will be the maximum distance of mm. Page 41 Chapter 3: Operation If Auto Tensioning is configured in the Supervisor Settings screen, the graph will appear as below while auto tensioning is in progress.
Once Auto Tensioning is complete, the PT will automatically begin the pull test. The blue line represents all readings. The pink line represents the moving average. The blue line repre- sents all readings. While the HMI is reconnecting, a Connecting message will appear in the bottom left corner of the screen.
Maximum peel force from a peel force test. Mean The average peel force from a peel force test. Range The minimum peel force test subtracted from the maximum peel force test. Page 46 Clicking on Save will bring up the screen below. This folder is automatically created when the software is installed.
Main Screen Details Page 47 Clicking on Open File will allow the operator to select from any previously saved jobs.. Reset Clicking Reset will prepare the software to perform another test using the same parameters as the test just completed.
Page 48 Press Home to reset position of carriage for next peel force. Exit The Exit button will close the PT software program. This button can be clicked at any time. All data which has not been saved will be erased. The Password Input screen will appear. Enter the password at the prompt and click OK. When Not Visible is selected, the field no longer appears in the Main Screen. This allows the operator to type in the desired information.
When the Pressure or Temperature fields are selected, an Operator entered double option appears under Input Type. This allows the supervisor to set the field data at a constant value that cannot be changed by the oper- ator. This allows the supervisor to create a selection drop box for the field.
0コメント