Supply-chain disruptions have hampered our ability to restock items reliably. We are doing what we can to adapt and recover from the changes to our industry, but currently many shipments are delayed and our response time to emails are slow we are severely short-staffed.
Even if we can't reply to your email promptly, please trust that we ARE working on getting delayed items back into stock for you, and we will contact you when we have any updated news.
We appreciate your continued support and understanding. When you place an online order request, you can opt to have in-stock items processed for shipment in advance of any backordered items. Requested items could be delayed by supplier-level backorder, and we usually aren't given reliable ETA information.
We work diligently to source and fulfill your request for items as best we can. Our site uses advanced code and encryption that is not supported by Microsoft's Internet Explorer Browser. This device lets you take the guesswork out!
Sensor Cable Overall length 10 ft. You will need to download the "Logworks" software from Innovate's website. Capable of removing stock or HD valve springs, without removing the engine Engine still in the car! This can really save your bacon!
This tool comes with the Rocker Shaft, Leverage Tool, and either a 12 or 14mm you choose the size Spark Plug insert to pressurize with air. When ordering, select the plug thread size you have to receive the proper air chuck adapter for your heads. If you have multiple sets of heads or are a tool "Junkie" , then get both 12 and 14mm for a small surcharge.
This tool comes with the Rocker Shaft and Leverage Tool. SImply slip the gear shoe under the gear, and with a twist of a wrench, the gear is easily removed. This deluxe model features an aluminum cap and swivel fitting makes install and removal a lot nicer! We recommend 10psi pressure, that's more than enough, and minimizes risk of blowing a supply line off big mess!
We recommend 10psi pressure, that's more than enough, and what we use on our own fleet of vanagons. Jet Reamer Kit Jet Drill Kit , All SIzes are not as good as using the proper sized jet, but drilling and reaming are acceptable if you go VERY slowly, and after you arrive at your proper jet size, measure and order the proper indexed jets!
This fits inside the barrel mouth of the carburetor. It also requires an adapter for Kadrons due to the centerally located air filter mounting stud. The reason you tap towards chamber is that carbon buildup on the chamber end of the guide would ream the guide hole in the head even further, loosening your press fit!
This bolts to the end of your frame horns and allows you to roll it around your shop with the trans axle out! This part does NOT come with any exhaust flange gaskets, you will need 2 good ones to make sure it doesn't leak!
If it leaks, you'll get "False Lean" readings on your O2 Gauge! We are in the midst of renovating our site! If you already have an order in process with us, don't panic!
Restock ETAs for backordered items are often either unavailable, or unreliable. We continue to answer emails as best we can, but we are operating with less than half of our normal staff, so please be patient.
Your understanding is appreciated while our company struggles to weather the challenges from Covid, and do what we still can to support the aircooled VW hobby. Our checkout system will re-open on Friday January 14th at am MST You may want to copy and paste to save the items your cart that includes links back to the items listings in order to save them, just in case your browser does not.
We hope that you will return when our online checkout resumes accepting new orders. Agree and Continue. VW Parts Catalog. Featured Brands. Join Our Mailing List. Immediate shipment of requested products is NOT guaranteed. Orders are processed in the order that they are received and order fulfillment time varies.
Actual product may differ in appearance. Please do NOT rely on PHOTOS while shopping as many of our products have selectable product options that may change the nature of the product being ordered compared to the representative photo. All information should be verified prior to use.
In most cases we are able to honor advertised price, but in the RARE case a substantial price increase occurs, you would be notified and given the option to cancel. All products purchased should be inspected, measured, cleaned and properly assembled prior to installation. Since Aircooled. Net has no control over product installation, we will not be held liable for any consequential costs or damages associated with products purchased. Gift Certificates. These conversion kits allow you to build a lightweight, portable, electric start air compressor our of VW parts, at a fraction of the cost of comparable models.
Many VW Enthusiasts probably have the stuff needed to build one of these lying around their garage! You also probably have a lot of the parts in your garage to build it, fix it, or give it a tune-up, and if the engine went bad, you probably know how to work on it too! You can also flycut the heads for more compression.
This tool comes with instructions and hardware. You can use this tool with a drill press. This tool is high quality, and built for repeated use. We do NOT have instructions other than what is supplied by the manufacturer for this particular product! This solves the problem of removing and replacing the round nut that retains the pinion bearing in the later VWs and later.
This tool is a lifesaver on stubborn pinion nuts! This will also remove Flanged Crank Flywheels, and even non-wedge mated flywheels. If you are wrenching a lot, or a racer, this is a nice tool to have. No more splitting the case, broken screw drivers , or chewed up flywheels! All the necessary hardware is included. Innovate LC-2 Wideband 4. This device lets you do it! Engine Stand, Floor Model, Square Tube Style, rotates a full degrees, and has steel casters for mobility. Knocks down when not in use to save space.
You can also use this to hold your transaxle! This allows you to easily use a mill or drill press in the "perpendicular" position for your work! Use a wrench with this tool, not a 20 ton press! For the smoothest operation, a ball-bearing swivel was engineered into this tools design and manufacturing. Bolts to a workbench or table, and rotates a full degrees.
This bench mount engine stand is the finest Bench Model Engine Stand you can have without making it yourself! Supply-chain disruptions have hampered our ability to restock items reliably. We are doing what we can to adapt and recover from the changes to our industry, but currently many shipments are delayed and our response time to emails are slow we are severely short-staffed.
Even if we can't reply to your email promptly, please trust that we ARE working on getting delayed items back into stock for you, and we will contact you when we have any updated news. We appreciate your continued support and understanding.
When you place an online order request, you can opt to have in-stock items processed for shipment in advance of any backordered items. Requested items could be delayed by supplier-level backorder, and we usually aren't given reliable ETA information.
We work diligently to source and fulfill your request for items as best we can. Our site uses advanced code and encryption that is not supported by Microsoft's Internet Explorer Browser. We are in the midst of renovating our site! If you already have an order in process with us, don't panic! Restock ETAs for backordered items are often either unavailable, or unreliable. We continue to answer emails as best we can, but we are operating with less than half of our normal staff, so please be patient.
Your understanding is appreciated while our company struggles to weather the challenges from Covid, and do what we still can to support the aircooled VW hobby. Our checkout system will re-open on Friday January 14th at am MST You may want to copy and paste to save the items your cart that includes links back to the items listings in order to save them, just in case your browser does not.
We hope that you will return when our online checkout resumes accepting new orders. Agree and Continue.
0コメント